3 Ways to Improve Your Fly Casting on the Flats

8 comments / Posted on / by

flycasting-in-saltwater

3 Ways to Improve Your Fly Casting on the Flats. Photo by: Louis Cahill

By Kent Klewein

About ten years ago, I embarked on my first international saltwater fly fishing trip, with a couple Texas boys I’d previously met while chasing peacock bass in the Amazon.

The saltwater trip took place down in Mexico, specifically the Ascension Bay area. Our primary target fish were bonefish but we kept a constant lookout for permit and tarpon. The two born and raised Texas boys had grown up fly fishing in the salt, and they both had more than enough testosterone, ego, and skill to handle the demanding fishing conditions. I on the other hand, had never experienced first hand the difficulties that saltwater fly fishing brings. I really struggled with spotting fish in an unfamiliar environment and managing my presentations in 25 mph winds. I’ll never forget the humbling feeling of defeat after our first day of fly fishing on the flats. My counterparts landed a dozen bonefish a piece while I only managed to catch one. Just about the entire trip I was plagued with the feeling of being under-gunned on the water. The wind totally kicked my butt and I missed numerous opportunities because I couldn’t cast far enough to consistently get my fly to the targets my guide was calling out.

At the time, the only problem I saw in my fly casting was I didn’t seem to have nearly as much power in my casting stroke as my buddies. That was true, but the real problem was I didn’t have the competency to diagnose what I was doing wrong and neither of my buddies did either. All they kept saying, over and over to me, was I needed to work on my double-haul.

Man, I wish I could go back in time, and relive that fishing trip in Mexico. I now know, I had three major flaws in my fly casting, and my double-haul wasn’t one of them. Below are the three problems I had on that Mexico trip with my fly casting. Each are areas newcomers to saltwater should pay close attention to and practice before they head down on a maiden fly fishing trip to the salt.

1st Problem: I tried to overcome the windy conditions by speeding up my casting stroke and casting with obnoxious amounts of muscle.

Good technique and timing can input far more power into the casting system than sheer muscle and effort. Casting as hard as I could worked against me ten fold. I wasn’t allowing the rod to do the work and I lost control of my casting stroke in the process. Both of which, ended up opening up my loops and keeping me from consistently laying out a straight leader on the water during my presentation. Lastly, all that muscle made it really challenging for me to stop my fly rod abruptly, and that didn’t allow me to smoothly and efficiently transfer the energy that I loaded into the rod during my forward cast or back cast.

2nD PROBLEM: I FAILED TO SHOOT LINE ON MY FINAL BACKCAST TO HELP ME PRE-LOAD MY FLY ROD.

Instead, I shot out all my fly line during my initial false casting, and didn’t do so on my final back cast. When you shoot line on your final back cast, it increases the amount of fly line into the system, and gets the head of the fly line moving and gaining momentum. That extra weight from the increased fly line and the momentum of the head moving away from the angler, will pre-load the rod when all of it straightens out on the back cast. When the final forward cast is timed correctly (started exactly at the moment when all of the fly line straightens out on the back cast) it will greatly increase the overall line speed and power generated into the casting system, because the angler will be able to load the rod deeper and smoother during the final forward cast. Plain and simple, an angler will be able to increase the distance they can cast a fly, and it won’t require any additional casting effort.

3rd Problem: I wasn’t allowing my fly line to completely straighten out on my final backcast.

Instead I was starting my forward cast prematurely, and all the fly line that failed to straighten out on my final back cast, was instantly turned into slack. All that slack sucked a significant portion of the power out of my fly casting, and it also greatly decreased the distance I could reach with my fly on the flats. It also gave me some tailing loops issues. You can get away with some slack in the cast when casting short distances or fishing in calm conditions for trout, but when you visit the salt, it’s crucial for you to keep the slack out of your fly casting with good timing. Always remember you cannot begin bending or loading your rod until you eliminate all slack. That holds true during the initial pickup of fly line and during all facets of the casting stroke.

Keep it Reel,

Come fish with us in the Bahamas!

Kent Klewein
Gink & Gasoline
www.ginkandgasoline.com
hookups@ginkandgasoline.com
 
Sign Up For Our Weekly Newsletter!
 

Follow Gink & Gasoline on Facebook:

8 thoughts on “3 Ways to Improve Your Fly Casting on the Flats

  1. Great Information in this article! Some good things to practice and keep a watch on in your cast. I am a sucker for increasing “muscle” during windy conditions at times as well.

    Matt

  2. Pingback: Casting from Gink and Gasoline | Bonefish on the Brain

  3. Terrific, as usual Kent. My good friend and tarpon guide extraordinaire Phil Chapman taught me much about casting from the deck, but the thing that got me to a different casting level with the 11 weight (for me anyway) was your third point. Opening up your upper body and arm some to allow that back cast to unfold is a key to controlled distance. It’s much like gaining more leverage as a baseball pitcher by opening up– but with the added component of increasing the loading of your fly rod and letting it work for you.

  4. Your second tip is a great suggestion. I’ve never heard that one before. I’ve slipped out line on the (hopefully) few false casts I need to work out the line that I need. I’ll try to put the bulk of the needed line out on the last back cast. Shooting line into the wind is also very challenging except while using a shooting head or overweighted line with my intermediate skills. Thanks for the tips.

  5. Pingback: Casting from Gink and Gasoline | Posts

  6. Pingback: Tippets: Joint Support for EPA’s “Clean Power,” Saltwater Casting Mistakes, TU Fights Maryland Fracking | MidCurrent

Leave a Reply to Ralph A. Cancel reply

Your email address will not be published.

Captcha loading...